STEAM TUG
"ROEK"
A handsome small tug built 1930 by Gebr. Windt.
20.25 mtr long x 5 mtr beam x 2.2 mtr.
165 H.P. triple expansion engine with oil fired Scotch boiler (new boiler fitted in 1980).
This tug has been fully restored and has excellent accomodation with all facilities.
Ready for immediate use! |
|
STEAM LAUNCH
"STICKLEBACK"
A 12 Ft 9" steam launch.
A well fitted out clinker hull in GRP, 5 Ft beam.
Steam engine 2" x 2 1/8" cylinder on 4 columns.
Coal fired monotube boiler.
A small, light boat with a purpose-built trailer.
With current boiler certificates.
SOLD |
|
COMPOUND
Marine Engine
2" + 5" x 6" Cylinders
With slide valves, on cast standards.
Wt est 250 Kg.
An early marine steam engine of elegant design.
In restored condition. |
|
COMPOUND LAUNCH ENGINE
A British made marine engine with reversing gear.
1 1/2" + 3 1/2" x 4" Cylinders
Approx 27" High, and 14" x 12" Wide at Feet.
A circa 1920's design with piston valves.
Suitable for a steam launch.
In good original condition. |
|
 TWIN HIGH PRESSURE
Marine Engine
2" + 2" x 4 1/4" Cylinders
29" High, Base 12" x 12".
Solid disc flywheel.
In good condition. |
|
LACK
Single Cylinder Launch Engine
Approx 4" x 4" Cylinder
Base 18" x 14", 32" high overall.
Slide valve with link reversing gear.
An attractive single cylinder steam launch
engine on turned columns with
attached boiler feed pump.
Solid disc flywheel.
Wt approx 70 Kg.
In good, restored condition. |
|
 REIDS
Twin High Pressure
Marine Engine
By Reids of Glasgow, c1900.
2.5" + 2.5" x 4" Cylinders
Slide valves with link reversing gear.
In good condition. |
|
 SIMPSON STRICKLAND
Auxiliary Marine Engine
Approx 3 1/2" x 4" Cylinder
Piston valve, on 4 turned columns.
Approx 21" High, solid flywheel 8" Dia.
A very rare, high quality small marine engine
made for auxiliary use in small steam boats.
In excellent condition. |
|
TWIN HIGH PRESSURE
Steam Engine
2 1/2" + 2 1/2" x 3" Cylinders
20" High, on Base 22" x 12".
A Marine type steam engine with slide valves
on six turned columns and with solid flywheel.
10" Dia flywheel.
In good condition. |
|
 RANSOMES, SIMS & JEFFERIES
Compound Marine Engine
With Radial Valve Gear
Approx 35 H.P.
~ Built c1905 ~
Complete with boiler, propeller and auxiliaries.
In good, original condition. |
|
Compound
Marine Engine
8" + 16" x 8" Cylinders with Slide Valves.
A very high class 2 cylinder engine of approx 60H.P. built for the Admiralty in 1942 at the LNER workshops, for use in a harbour service launch.
Crosshead driven boiler feed, air and bilge pumps.
All mounted on turned steel columns, and with integral thrust block.
Engine believed fully restored mechanically, and ready for installation in a suitable hull. |
|
350 H.P. Compound
Marine engine
18" + 31" x 16" Cylinders
Approx 336 IHP at 130 r.p.m.
Turned front columns, cast back standards.
Stevenson link reversing gear.
Complete with pump, lubricators and thrust bearings.
Built 1893 in Jonkoping, Sweden.
In good condition. |
|
GEBRÜDER SACHSENBERG
1897 Compound Marine Engine
210 mm + 365 mm x 31 mm Cylinders
Approx 45 - 50 IHP.
By Gebrueder Sachsenberg of Rosslau, Germany.
Turned front columns, cast back standards.
Slide valves on HP and LP cylinders.
Attached air, condenser circ. & boiler feed pumps.
A beautifully restored early German marine engine. |
|
